Making Art Clay Silver Heart Set with Stones Tutorial

Make a beautiful textured heart set with stones perfect as jewelry gifts for significant occasions such as birthday, Valentine’s Day, or any special occasion using Ary Clay Silver. Here is Making Art Clay Silver Heart Set with Stones Tutorial.

Steps on How to Make an Art Clay Silver Heart Set with Stones

You will need:

• • 7g Art Clay Silver
  • Art Clay Silver Syringe
  • Heart Cutter pack set 6
  • Brass Plate Large Flowers

• Synthetic Ruby, Round, 3,4,5mm, Pack of 14
• Sterling Silver 12/18 Plain Trace, Loose
• Sterling Silver Bolt Ring Closed 6mm, Pack of 10
• Jump rings – made from Sterling Silver Round Wire 1.00mm, Fully Hard, 30gm Coils
• Oxidising Solution 500ml Un2818 C
• Bicarbonate of soda

Tools required:

• Badger Balm For Hardworking Hands, 21g/0.75 Oz
• Needle Tool
• Clay Shapers, Set Of 5, Size O
• Cutter Flexible Safety Curved Edge
• Wooden Handle Brass Brush 4 Row
• Acrylic Roller 25 X 175mm
• Plastic Spacers 1.5mm Pack of 2
• Plastic Spacers 1mm Pack of 2
• Emery papers in various grades
• Either a kiln or a torch to fire the pieces
• Tiles to use as a work surface

Step #1 – Rolling out the Clay and Texturing

Spread Badger Balm on a tile, the brass texture plate, and your hands.

Using the thicker spacers, roll out the clay so that it is of a size you can almost fit the cutter on.

Lift the clay using the flexible cutter, place it on the brass texture plate and align your thinner spacers or playing cards next to the clay but on top of the texture plate.

Roll the clay once with confidence to add texture, then use the flexible cutter to lift the clay and turn it over onto the tile with the texture facing upwards. See the figure below.

Step #2 – Cutting the Shapes

Choose 2 cutters with at least 2mm difference in size for the pendant and the same for the earrings. Remember that the clay will shrink about 8-9% depending on your method of firing.

Cut out the outside shape, then position the smaller cutter on the clay until you are happy. Slightly offset to add to the handmade look and design.

Cut the inside shape. Remove the excess clay from the outside of the shape and the inside shape using the needle tool.

Repeat steps 1 and 2 until you have a pendant shape and two earring shapes. Dry these pieces in your normal way.

Note: Use a kitchen hostess tray for food warming to dry my clay pieces, but you can use tea warmers, dehydrator, or some kilns to have a drying program.

If you do not have any of this equipment, leave your pieces somewhere warm to dry out overnight.

Step #3 – Setting the Stones

Take a small piece of art clay about twice the size of the stone and roll into a ball. Choose your stone and gently press it into the clay until the table of the stone is below the surface of the clay.

You can use cards or spacers on each side of the ball and the roller to get a perfectly flat stone table, just make sure you have enough clay underneath the stone, or you will get a dimple or hole after firing.

If the surround is too big, you can cut the clay while wet, but be careful you don’t pull the clay away from the stone, or it will just drop out of the setting.

The other alternative is to sand it down after drying and save the sandings to make a paste. Dry the stones in your normal way. Learn more about Making Art Clay Silver Heart Set with Stones Tutorial.

Step #4 – Sanding the Pieces

Using sanding pads, then several grits of emery papers, sand the base, sides, and inside of your pieces until they are smooth. Usually, go down to about 6000 grit.

The more time you spend at this stage of the process, the better the finish after firing. For heavy sanding or to sand the inside of the shapes, you can also use needle files.

Make sure all sandings are removed from the top of the stones as any specks will fire into solid silver and stick to the stone, and you will be able to see them on the finished piece. A soft brush is very useful for this.

Always support the area you are sanding, so you don’t accidentally break the piece as it is very fragile. Only use very little pressure, let the papers do the work for you.

Step #5 – Attaching the Stones

Once your pieces are sanded, it is time to attach the stones. Decide where you want to attach the stone, squirt a small amount of paste on the pendant/earring piece, then brush a small amount of water on the stone.

Press the wet part of the stone against the pendant/earring piece and hold until it starts to stick. Gently use the rubber-tipped tools to wick away any visible excess art clay from the front of the piece.

It will still be soft, so be very careful you don’t press too hard and move the stone away from its position.

Dry the piece, then use the paste to fill in any gaps on the rear of the piece and again dry the piece. Repeat step 4 until you are happy your piece is smooth.

You should be able to see a dark grey color to the piece if you have refined it enough.

Step #6 –Firing

Your pieces need to be dry before firing to prevent bubbles and holes.

Drill small holes in each piece to make room for the ear wires or jump rings. When you drill the hole, it is advisable to use a hand drill and not to put any pressure on the piece as it is very fragile.

Once you are happy with how the piece looks, it is ready for firing. Any lumps/bumps/scratches you can see now will be visible after firing, so make sure they are removed by sanding or filling with paste.

3 Methods of Firing your Piece:

Method #1 – Using a Kiln

The packaging suggests firing at 650 deg C, which is the minimum firing temperature. Firing at 830 deg C for about 35 minutes gives the best results and stronger pieces.

As the pieces have stones in, it is best to let the pieces cool completely before removing from the kiln, do not be tempted to cool them using water as this will crack the stones.

Method #2 – Torch Firing

You can fire the pieces using a cook’s torch such as ‘Hand Torch. Please Note Jewellers Torch Is Supplied Without Gas – 999 955’.

Place the piece on a solder block or heatproof surface and gently heat each piece separately until they glow pale orange and hold at this temperature for 3-4 minutes each piece. The binder will catch fire, just keep heating till the flames die away.

Move the piece out of the way to cool. Don’t be tempted to cool in the water, or this will crack the stones.

Method #3 – On a Gas Hob

Place the grid over your hob and switch the gas on. Once it is up to temperature, carefully add your pieces and leave in the hot areas for 7-10 minutes. Again, allow cooling gently to protect the stones.

Once fired, the pieces will appear white but are now solid silver. Rub a brass brush over the pieces until they are all silver.

You can now use the emery papers wet to add a final polish to the back and sides of the pieces if required. See the figure below.

Step #7 –Adding Color

To pick out the texture detail, use a solution of the liver of sulfur (oxidizing liquid) and warm water. The hotter the water you use, the quicker the silver will go black.

You can get a range of colors from golden through to black using the correct temperature and dipping the piece in for different times.

Add a little liver of sulfur solution to a heatproof pot, and pour over some warm water. In another pot make up a solution of bicarbonate of soda and water to neutralize the liver of sulfur.

Use plastic tweezers to dip the piece into the liver of sulfur solution. Dip in for a few seconds and lift out to check the color.

Once you are happy with the color, drop it into the bicarbonate of soda solution.

Step #8 –Polishing

Take the pieces out of the bicarb of soda solution and dry off with some kitchen roll. Add a little polish to a soft cloth and rub it into the cloth.

Rub the pieces with the polish impregnated cloth until you are happy with the result.

This will polish the raised areas of the texture while leaving the deeper areas colored so highlighting the pattern and adding depth to the piece. Make sure you polish the back too.

Step #9 – Finishing your Pieces

Once polished, add a jump ring to the pendant piece and make up your chain using the chain, bolt rings and jump rings. Add ear wires to your earrings. Making Art Clay Silver Heart Set with Stones Tutorial.

P.S. Royi Sal Jewelry, as a decades-long leader in silver jewelry design and manufacturing, invites you to download our latest magazine here and profit from the exceptional jewelry designs at affordable prices you will find in the magazine. Click here to download it now.